Almost everyone seems to have their own unique thoughts when it comes to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Mounting a bathtub isn't exactly rocket science, however it does call for solid plumbing, carpentry, and also sometimes, tiling skills. Replacing an old tub with a brand-new one is additionally a moderately difficult job. If the old bathtub is conveniently easily accessible, the project can move immediately; if you have to open a wall to get rid of the old tub as well as place the new tub, the job is much harder. In either instance, the job is within a residence handyman's abilities, although you will require an assistant to vacate the old tub as well as embeded in the new one. Ensure you have certified on your own for the job and fit trying it. Rather than hiring a service provider to take over a halfway-completed job, it is far better to think about using one before you start. Chances are you may require a professional plumber to make tube connections.
This short article will certainly help you set up a brand-new bathtub in your shower room if you have actually already gotten a brand-new bathtub as well as do not require to transform the arrangement of your previous water system pipelines.
Your devices and material list must comprise the following:
Planning for the Setup
Firstly, the sustaining frame provided with the bath must be fitted (if required) according to the supplier's instructions. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is necessary to ensure that if the faucet includes a plastic washer, it is fitted in between the bath and the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the taps unit to stop pressure on the tub.
Fit the flexible tap adapters to the bottom of both taps using 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you make use of every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be suited its final position.
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your setup, then the first thing you need to do is detach the supply of water. After doing so, turn on the faucets to drain any type of water remaining in the system. The procedure of eliminating the existing taps can be fairly troublesome due to the restricted accessibility that is often the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipes. When the supply pipelines have actually been eliminated, make use of the exact same device to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from transforming during this process. As soon as the faucets have been removed, the holes in the bath/basin will certainly need to be cleaned up of any kind of old securing compound.
Before going on to fit the brand-new taps, compare the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Setting up the Tub
Using both wood boards under its feet, put the bathtub in the called for setting. The wooden boards are useful in equally spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 little points.
The following objective is to guarantee that the bath tub is leveled all round. This can be accomplished by checking the spirit level and also changing the feet on the bathtub till the spirit level reads level.
To install taps, fit the bottom of the furthest versatile tap adapter to the suitable supply pipeline by making a compression join; after that do the same for the other tap.
Turn on the supply of water and also inspect all joints and also new pipework for leaks and also tighten them if required. Fill the bath tub and also examine the overflow outlet and the typical outlet for leakages.
Finally, repair the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as securing around the tub needs to wait until the bathtub has actually been utilized a minimum of once as this will certainly settle it into its last setting.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic port to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet and also the other end gives a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly need decreasing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, place the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines remain in area between the faucet and the sink. Safeguard the tap in place with the maker offered backnut. Once the faucet is securely in position, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular faucet ports. The former kind ought to be attached to the faucet ends initially, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the location where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to fracture a rigid seal, creating the water to penetrate the wall surface between the bath and also the tiling, causing complications with moisture and possible leakages to the ceiling below.
You can choose from a range of coloured sealers to assimilate your fixtures as well as fittings. They are offered in tubes and also cartridges, and can sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched paper or soft rope. Remember to always fill up the tub with water prior to sealing, to allow for the motion experienced when the bathtub remains in use. The sealer can break relatively very early if you do not take into account this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently available on the market. It is recommended to fit the ceramic tiles utilizing water-resistant or water resistant sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like more info about How to Install a Bathtub Yourself? Give a remark directly below. We would be delighted to listen to your ideas about this article. We are looking forward that you visit us again later on. If you enjoyed our blog posting plz remember to pass it around. Many thanks for your time. Visit again soon.
Click Here To Read More